| |
PERLNETWARE(1) Perl Programmers Reference Guide PERLNETWARE(1)
NAME
perlnetware - Perl for NetWare
DESCRIPTION
This file gives instructions for building Perl 5.7 and above, and also
Perl modules for NetWare. Before you start, you may want to read the
README file found in the top level directory into which the Perl source
code distribution was extracted. Make sure you read and understand the
terms under which the software is being distributed.
BUILD
This section describes the steps to be performed to build a Perl NLM
and other associated NLMs.
Tools & SDK
The build requires CodeWarrior compiler and linker. In addition, the
"NetWare SDK", "NLM & NetWare Libraries for C" and "NetWare Server Pro-
tocol Libraries for C", all available at , are also required. Microsoft Visual C++ version 4.2 or
later is also required.
Setup
The build process is dependent on the location of the NetWare SDK.
Once the Tools & SDK are installed, the build environment has to be
setup. The following batch files setup the environment.
SetNWBld.bat
The Execution of this file takes 2 parameters as input. The first
being the NetWare SDK path, second being the path for CodeWarrior
Compiler & tools. Execution of this file sets these paths and also
sets the build type to Release by default.
Buildtype.bat
This is used to set the build type to debug or release. Change the
build type only after executing SetNWBld.bat
* Example:
1. Typing "buildtype d on" at the command prompt causes the
buildtype
to be set to Debug type with D2 flag set.
2. Typing "buildtype d off" or "buildtype d" at the command
prompt causes
the buildtype to be set to Debug type with D1 flag set.
2. Typing "buildtype r" at the command prompt sets it to Release
Build type.
Make
The make process runs only under WinNT shell. The NetWare makefile is
located under the NetWare folder. This makes use of miniperl.exe to
run some of the Perl scripts. To create miniperl.exe, first set the
required paths for Visual c++ compilier (specify vcvars32 location) at
the command prompt. Then run nmake from win32 folder through WinNT
command prompt. The build process can be stopped after miniperl.exe is
created. Then run nmake from NetWare folder through WinNT command
prompt.
Currently the following two build types are tested on NetWare:
o USE_MULTI, USE_ITHREADS & USE_IMP_SYS defined
o USE_MULTI & USE_IMP_SYS defined and USE_ITHREADS not defined
Interpreter
Once miniperl.exe creation is over, run nmake from the NetWare folder.
This will build the Perl interpreter for NetWare as perl.nlm. This is
copied under the Release folder if you are doing a release build, else
will be copied under Debug folder for debug builds.
Extensions
The make process also creates the Perl extensions as .nlm>
INSTALL
To install NetWare Perl onto a NetWare server, first map the Sys volume
of a NetWare server to i:. This is because the makefile by default sets
the drive letter to i:. Type nmake nwinstall from NetWare folder on a
WinNT command prompt. This will copy the binaries and module files
onto the NetWare server under sys:\Perl folder. The Perl interpreter,
perl.nlm, is copied under sys:\perl\system folder. Copy this to
sys:\system folder.
Example: At the command prompt Type "nmake nwinstall".
This will install NetWare Perl on the NetWare Server.
Similiarly if you type "nmake install",
This will cause the binaries to be installed on the local
machine.
(Typically under the c:\perl folder)
BUILD NEW EXTENSIONS
To build extensions other than standard extensions, NetWare Perl has to
be installed on Windows along with Windows Perl. The Perl for Windows
can be either downloaded from the CPAN site and built using the
sources, or the binaries can be directly downloaded from the ActiveS-
tate site. Installation can be done by invoking nmake install from the
NetWare folder on a WinNT command prompt after building NetWare Perl by
following steps given above. This will copy all the *.pm files and
other required files. Documentation files are not copied. Thus one
must first install Windows Perl, Then install NetWare Perl.
Once this is done, do the following to build any extension:
o Change to the extension directory where its source files are
present.
o Run the following command at the command prompt:
perl -II -II Makefile.pl
Example:
perl -Ic:/perl/5.6.1/lib/NetWare-x86-multi-thread -Ic:\perl\5.6.1\lib MakeFile.pl
or
perl -Ic:/perl/5.8.0/lib/NetWare-x86-multi-thread -Ic:\perl\5.8.0\lib MakeFile.pl
o nmake
o nmake install
Install will copy the files into the Windows machine where NetWare
Perl is installed and these files may have to be copied to the Net-
Ware server manually. Alternatively, pass INSTALL-
SITELIB=i:\perl\lib as an input to makefile.pl above. Here i: is
the mapped drive to the sys: volume of the server where Perl on
NetWare is installed. Now typing nmake install, will copy the files
onto the NetWare server.
Example: You can execute the following on the command prompt.
perl -Ic:/perl/5.6.1/lib/NetWare-x86-multi-thread -Ic:\perl\5.6.1\lib MakeFile.pl
INSTALLSITELIB=i:\perl\lib
or
perl -Ic:/perl/5.8.0/lib/NetWare-x86-multi-thread -Ic:\perl\5.8.0\lib MakeFile.pl
INSTALLSITELIB=i:\perl\lib
o Note: Some modules downloaded from CPAN may require NetWare related
API in order to build on NetWare. Other modules may however build
smoothly with or without minor changes depending on the type of
module.
ACKNOWLEDGEMENTS
The makefile for Win32 is used as a reference to create the makefile
for NetWare. Also, the make process for NetWare port uses miniperl.exe
to run scripts during the make and installation process.
AUTHORS
Anantha Kesari H Y (hyanantha@novell.com) Aditya C (caditya@novell.com)
DATE
o Created - 18 Jan 2001
o Modified - 25 June 2001
o Modified - 13 July 2001
o Modified - 28 May 2002
perl v5.8.8 2006-01-07 PERLNETWARE(1)
|